Dec 21, 2022 Detailed New HPE0-S60 Exam Questions for Concept Clearance [Q24-Q46]

4/5 - (1 vote)

Dec 21, 2022 Detailed New HPE0-S60 Exam Questions for Concept Clearance

HPE0-S60 Exam Preparation Material with New HPE0-S60 Dumps Questions.

Q24. Your customer plans to add four HPE Synergy frames to an existing management ring Ail installed frames are equipped with two 2-port FLM modules, while new frames will be equipped with 4-port FLM modules.
Which statement about mixing different FLM modules is true?

Existing 2-port FLM modules must be replaced with 4-port FLM modules

A management ring can contain mixed frame link module configurations

A management ring with mixed FLM modules cannot have more than 12 frames

Mixing different FLM modules is allowed if all of them have the same firmware version

Q25. Your customer plans to use HPE OneView for VMware vCenter Server to deploy ESXi systems. They created a server profile template that they want to use in HPE OneView.
Put the steps required to configure HPE OneView for VMware vCenter Server on the left into their correct order on the right.

Q26. Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They also plan a vSAN deployment leveraging HPE D3940 Storage Modules and SSD drives The customer requested the following components:
– HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
– Two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
– An appropriate number of vSAN Standard licenses for each compute node
– One HPE O3940 Storage Module with 40 SSDs – All required cables and options Which statement about this request is true?

vSphere licenses should be added, as vSAN licenses do not replace vSphere licenses

vSphere Standard licenses should be replaced with Enterprise Plus licenses to enable vSAN

One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50GD/S ILM

20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drives.

Q27. You are troubleshooting an HPE OneView server profile that presents a critical state. The server profile was configured with a Link Aggregation Group What should you check to fix the issue?

if both FiexNICs are configured with the same speed

If the logical enclosure is built on at least three HPE Synergy frames

if both FiexNICs are connected to different networks

if the logical enclosure is configured with redundant master modules

Q28. Your customer wants to add dedicated Fibre Channel connectivity to the HPE Synergy frame running HPE Synergy 480 Gen10 compute modules, each with one CPU socket populated Currently they use two 12 Gb SAS switches and two HPE Virtual Connect SE 100Gb F32 Modules for HPE Synergy installed in third fabric.
What must be done to enable dedicated FC connectivity for this HPE Synergy frame?

A second CPU must be installed for all HPE Synergy 480 Gen10 compute nodes.

For Brocade switches, a logical interconnect group must be created in HPE OneView.

For VC-FC modules, all of server facing ports must be property licensed.

SAS switches must be moved to second fabric and FC modules Installed in the first one.

Q29. Which statement about manual orchestration during the firmware update is true?

It is supported only for logical enclosures with at least three frames

It provides an ability to select and update one side of the Interconnect topology at a time

It provides the ability to install an older firmware version than currently Installed In the interconnect

It allows all the interconnect modules to be activated manually at the same time.

Q30. Your customer plans to deploy ESXi systems to HPE Synergy and HPE ProLiant servers using HPE OneView for VMware vCenter Server.
Which statement about HPE OneView for VMware vCenter Server functionality is true for this environment?

HPE ProLiant servers need an HPE OneView for VMware vCenter Server license for full functionality

Individual systems can be added to HPE OneView for VMware vCenter Server through an ILO management processor

HPE Synergy requires HPE Composer 2 for full functionality of HPE OneView for VMware vCenter Server

Only systems managed using HPE Oneview can use HPE Oneview for VMware vCenter Server functionalities

Q31. A logical interconnect group can span on multiple HPE Synergy frames for which interconnect type?

HPE Synergy 12 Gb SAS Connection Module

HPE virtual Connect SE 32 Gb FC Module for Synergy

Brocade 32GB Fibre Channel Switch Module for HPE Synergy

HPE Virtual Connect SE 100 Gb F32 Module tor Synergy

Q32. Your customer plans to deploy VMware vSAN using D3940 Storage Modules.
Which statement about this solution is true?

The 12Gb SAS modules required for D3940 connectivity can only be installed in the first fabric.

To use the storage controller that will access D3940 storage modules, a second CPU must be installed.

For VMware vSAN deployment, all drives in the D3940 storage modules must be SSD drives.

All drives in the D3940 storage modules must formulate a single logical drive with RAID5 configured

Q33. Click the area within the iLO management interface that will allow you to access workload Advisor.

Q34. Match each HPE OneView network type with its definition.

Q35. You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support Which interconnects are required to support this connection? (Select two.)

HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy

HPE Virtual Connect SE 16Gb FC Module for HPE Synergy

HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy

HPE Virtual Connect SE 32Gb FC Module for HPE Synergy

Brocade 16Gb Fibfe Channel SAN Switch Module for HPE Synergy

Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy

Q36. In the past a customer experienced a networking issue where network ports went down and came back up in quick succession.
Which HPE Virtual Connect SE 100 GD F32 Module for HPE Synergy feature can be configured to disable such ports?

Pause flood protection

sFlow

Storm control

Port flap protection

Q37. Refer to the exhibit.

Which statement about this logical interconnect group is true?

The master modules are located in the interconnect bays 2 and 5

For the given downlink speed, the maximum number of frames is reached

Both master modules are located in the same HPE S ynergy frame

To use interconnect bay set 3, all compute nodes must be half-height

Q38. What is a limitation when creating a server profile?

BIOS settings can be changed only when UEFI optimized is selected as boot mode

ILO management is limited to the integration with Active Directory or LDAP

Administrator cannot define more than 8 connections within a server profile

It is not possible to create shared volumes on demand through a server profile

Q39. Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol What must be done to complete this task?

Enable FC primary and secondary boot on the modules through the HPE OneView interface

FC connectivity on the modules should be enabled through the service console by disabling FCoE.

Add FC upgrade licenses in HPE OneView that will enable FC connectivity for the modules

Enter both modules into a maintenance mode, then enable FC connectivity through CLI

Q40. You need to setup HPE Synergy frames after hardware components are discovered within HPE OneView.
Put the steps to achieve this goal into the coned order in the answer area on the right.

Q41. Which statement about login redistribution is true?

Q42. After deploying HPE Superdome Flex 280 you need to check Core Analysis Engine (CAE) Log.
Click the appropriate section in the HPE Superdome Flex 280 management interface that will allow you to complete this task.

Q43. Click the drop-down menu that will allow you to define the location of the master modules within the logical interconnect group.

Q44. Your customer has me following HPE Synergy setup
– Three frames fully populated with HPE Synergy 480 Gen10 Plus modules and 25Gb/s downlink speed formulating a single logical enclosure
– Two HPE Virtual Connect SE 100Gb F32 Module for Synergy
– Four HPE Synergy 50Gb interconnect Link Module
– Six HPE Synergy Virtual Connect SE 32Gb FC Modules
The customer needs to add a frame.
Which statement about the expansion of this setup is true?

The additional frame must have HPE Virtual Connect FC modules installed

The customer can grow the existing logical enclosure up to 5 frames

The customer has to create a new logical enclosure for the additional frame

The additional frame cannot have 12Gb SAS connection modules installed

Q45. Your customer plans to deploy VMware ESXi 7. 0 U2, and they are looking for a hardware platform that will allow them to use up to 16 CPU sockets Which HPE compute system meets the customer requirements?

HPE ProLiant DL580 Gen10

HPE ProLiant OL380 Gen 10 Plus

HPE Synergy 480 Gen10 Plus

HPE Superdome Flex system

Q46. What is a restriction of using a RoCE network?

It is by default configured as an untagged network and cannot be a part of a network set.

It does not support Private VLAN and Multicast VLAN.

it is not supported with HPE Virtual Connect SE 40 GD F8 Module for HPE Synergy.

It does not support smart link and private network features.